LTC4350
4350fb
applicaTions inForMaTion
The resistors R
OUT
and R
SET
set the adjustment range.
The voltage on R
SET
is translated to a voltage on R
OUT
by the ratio of R
OUT
/R
SET
. Therefore, the adjustment on
the output voltage will track the voltage at the R
SET
pin
which is also the voltage on the COMP2 pin minus a diode
voltage. The expression is V
ADJ
= (V
RSET
) " R
OUT
/R
SET
=
(V
COMP2
V
DIODE
) " R
OUT
/R
SET
. The maximum voltage at
V
RSET
is limited to 1V . The maximum adjustment on the
output is expressed as V
ADJMAX
= R
OUT
/R
SET
. A normal
value for R
SET
is in the 50?to 100?range.
If we set R
SET
to be 100? then an R
OUT
of 100?allows
the output voltage a full 1V adjustment. For the 0.3V range
in this example, the R
OUT
is 30? In some power modules,
there already exists a resistor between the SENSE
+
line
and the power output. In this case, the value of R
OUT
is the
parallel combination of two resistors, one in the module
and one placed between the SENSE
+
and output terminals
of the module.
The value of the gain setting resistor, R
GAIN,
depends on
the maximum voltage drop across the sense resistor and
the supply voltage V
CC
for the chip. The highest possible
voltage at the GAIN pin is 1.5V from the V
CC
voltage.
The maximum voltage on the GAIN pin is expressed as:
V
GAINMAX
= R
SENSE
" I
MAX
" R
GAIN
/1k = V
CC
1.5V . The
expression for R
GAIN
: R
GAIN
= (V
CC
1.5V) " 1k/(R
SENSE
"
I
MAX
). In this example, V
CC
is 5V , I
MAX
is 20A and R
SENSE
is 0.002? Therefore, R
GAIN
is 87.5k but using 1% values
results in 86.6k.
The FB pin divider provides a 1.220V output for a 5V
input. The precision of the FB pin divider resistors will
impact the accuracy of the final output voltage. The UV
resistive divider in this example, turns on the gate when
V
CC
increases above 4V . This corresponds to the UV pin at
1.220V . The capacitor C
UV
prevents false activation during
load steps. The OV set point needs to occur above the
adjustment max for V
CC
. The power supply output (which
also is V
CC
), can start as high as 5V and adjust upwards
to 5.3V . The OV set point in this example is 5.5V on V
CC
when the OV pin is at 1.220V .
The timer capacitor C
T
is set to be 0.1礔 for a 61ms
timer cycle. The expression is t = C
T
" 1.22V/2礎. The
gate capacitor C
G
is set to be 0.1礔 which sets a slope
of 10礎/C
G
or 1V every 10ms. In this case, the GATE pin
must charge up to 9V before the output can ramp to 5V
which happens in 90ms. In this case, the output adjust
soft-start turns on when the gate ramps above 9V . The
soft-start circuitry releases the COMP2 pin allowing the
load sharing loop to function. A 100?resistor R
G
prevents
high frequency oscillations from the power FETs at their
turn-on threshold. A 0.1礔 bypass capacitor is required on
the V
CC
pin. If the V
CC
pin is tied to the same power sup-
ply output that is being adjusted, then a 51?decoupling
resistor is needed to hold up the supply during a short to
ground on the supply output.
COMPENSATION
The compensation capacitor, C
P1
, is needed to set the
crossover frequency of the feedback error amplifier E/A1.
The crossover frequency of 200kHz is adequate for most
applications and requires C
P1
to be 1000pF (0.001礔).
The design of the other compensation capacitor will require
some knowledge about the power supplys bandwidth. The
bandwidth can be measured easily. First, use a storage
oscilloscope to monitor the power supply output voltage.
Then place a 1A resistive fixed load and switch in a second
resistive load that increases the total load current close
to rated maximum. Tapping the second resistor (with
the correct power rating) to the power supply output
creates this load step. Trigger the scope on the falling
edge of the output voltage as it drops more than 100mV
(for example from 5V to 4.8V). The recovery time, t
R
,
from the step needs to be measured. t
R
is defined as
the 10% to 90% time measurement (see Figure 6). The
4350 F06
t
t
r
0.1V
V
0.1V
90%
10%
Figure 6. t
R
Measurement
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
MAX1299CEAE+
IC TEMP SENS W/ADC 16-SSOP
MAX14544ETA+T
IC ACCY SWITCH OVP PROTECT 8TDFN
MAX1617AMEE+T
IC REMOTE/LOCAL TEMP SNSR 16QSOP
MAX1617MEE+T
IC REMOTE/LOCAL TEMP SNSR 16QSOP
MAX1619MEE+
IC TEMP SENSOR W/ALARM 16-QSOP
MAX1765EUE+
IC REG DL BST/LINEAR 16TSSOP
MAX1989MUE+
IC TEMP SENSOR REMOTE 16TSSOP
MAX31723MUA+
IC THERMOMETER/STAT SPI-3W 8UMAX
相关代理商/技术参数
LTC4350IGN#TR
功能描述:IC CNTRLR HOTSWAP LOADSHAR16SSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program 标准包装:119 系列:- 类型:热交换控制器 应用:通用型，PCI Express? 内部开关:无 电流限制:- 电源电压:3.3V，12V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:80-TQFP 供应商设备封装:80-TQFP（12x12） 包装:托盘 产品目录页面:1423 (CN2011-ZH PDF)
LTC4350IGN#TRPBF
功能描述:IC CNTRLR HOTSWAP LOADSHAR16SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program 标准包装:119 系列:- 类型:热交换控制器 应用:通用型，PCI Express? 内部开关:无 电流限制:- 电源电压:3.3V，12V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:80-TQFP 供应商设备封装:80-TQFP（12x12） 包装:托盘 产品目录页面:1423 (CN2011-ZH PDF)
LTC4352CDD#PBF
功能描述:IC IDEAL DIODE CNTRL 12-DFN RoHS:是 类别:集成电路 (IC) >> PMIC - O 圈控制器 系列:- 标准包装:1,000 系列:- 应用:电池备份，工业/汽车，大电流开关 FET 型:- 输出数:5 内部开关:是 延迟时间 - 开启:100ns 延迟时间 - 关闭:- 电源电压:3 V ~ 5.5 V 电流 - 电源:250µA 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:16-SOIC（0.154"，3.90mm 宽） 供应商设备封装:16-SOIC N 包装:带卷 (TR)
LTC4352CDD#TRPBF
功能描述:IC IDEAL DIODE CNTRL 12-DFN RoHS:是 类别:集成电路 (IC) >> PMIC - O 圈控制器 系列:- 标准包装:1,000 系列:- 应用:电池备份，工业/汽车，大电流开关 FET 型:- 输出数:5 内部开关:是 延迟时间 - 开启:100ns 延迟时间 - 关闭:- 电源电压:3 V ~ 5.5 V 电流 - 电源:250µA 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:16-SOIC（0.154"，3.90mm 宽） 供应商设备封装:16-SOIC N 包装:带卷 (TR)
LTC4352CMS#PBF
功能描述:IC IDEAL DIODE CNTRL 12-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - O 圈控制器 系列:- 标准包装:1,000 系列:- 应用:电池备份，工业/汽车，大电流开关 FET 型:- 输出数:5 内部开关:是 延迟时间 - 开启:100ns 延迟时间 - 关闭:- 电源电压:3 V ~ 5.5 V 电流 - 电源:250µA 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:16-SOIC（0.154"，3.90mm 宽） 供应商设备封装:16-SOIC N 包装:带卷 (TR)
LTC4352CMS#TRPBF
功能描述:IC IDEAL DIODE CNTRL 12-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - O 圈控制器 系列:- 标准包装:1,000 系列:- 应用:电池备份，工业/汽车，大电流开关 FET 型:- 输出数:5 内部开关:是 延迟时间 - 开启:100ns 延迟时间 - 关闭:- 电源电压:3 V ~ 5.5 V 电流 - 电源:250µA 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:16-SOIC（0.154"，3.90mm 宽） 供应商设备封装:16-SOIC N 包装:带卷 (TR)
LTC4352HDD#PBF
功能描述:IC IDEAL DIODE CTLR W/MON 12-DFN RoHS:是 类别:集成电路 (IC) >> PMIC - O 圈控制器 系列:- 标准包装:1,000 系列:- 应用:电池备份，工业/汽车，大电流开关 FET 型:- 输出数:5 内部开关:是 延迟时间 - 开启:100ns 延迟时间 - 关闭:- 电源电压:3 V ~ 5.5 V 电流 - 电源:250µA 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:16-SOIC（0.154"，3.90mm 宽） 供应商设备封装:16-SOIC N 包装:带卷 (TR)
LTC4352HDD#TRPBF
功能描述:IC IDEAL DIODE CTLR W/MON 12-DFN RoHS:是 类别:集成电路 (IC) >> PMIC - O 圈控制器 系列:- 标准包装:1,000 系列:- 应用:电池备份，工业/汽车，大电流开关 FET 型:- 输出数:5 内部开关:是 延迟时间 - 开启:100ns 延迟时间 - 关闭:- 电源电压:3 V ~ 5.5 V 电流 - 电源:250µA 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:16-SOIC（0.154"，3.90mm 宽） 供应商设备封装:16-SOIC N 包装:带卷 (TR)